Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterLiftMaster Gate Repair in North Hollywood: What to Know First
LiftMaster gate repair in North Hollywood is work we handle every week, and most jobs are completed in a single visit. As an independent LiftMaster service provider, we repair the opener, the gate itself, and the hardware that ties them together: hinges, posts, locks, welds, and wiring. Our pricing is settled in writing before a single bolt is turned, and every repair is covered by our 90-Day Done Right Promise. Call (925) 693-7978 and a live person answers – day or night.
How LiftMaster Products Fail – and How We Fix Them
- LA400 and LA500 slide gate operators burning out the limit switches. The LA400 is a workhorse on North Hollywood driveways, but its limit switch assembly sits close to the ground and takes on dust and moisture. When the limit switch fails, the gate opens fine and then drifts or slams at the end of travel. We replace the switch with an OEM part, then reseal the housing so the same failure does not come back next season.
- CSL24V and CSW24V control boards dying after power surges. These 24-volt operators are common on estate gates in the hills above Burbank Boulevard. The boards are sensitive to the voltage spikes that come with Valley heat waves and rolling brownouts. The symptom is usually a gate that hums but will not move, or an opener that forgets its remote codes. We replace the board and add a surge protector at the breaker – a $60 part that saves a $400 board.
- MCT and MCT-3 gate openers with stripped drive gears. These low-voltage openers are popular on pedestrian gates and smaller driveway gates. The drive gear is made of a softer metal than the worm it rides against, so it wears down over time. The telltale sign is a gate that labors and groans before it finally stops moving. We rebuild the gearbox with OEM gears and regrease the unit with the correct low-temperature grease printed in the service manual.
- K74 and K75 keypads with corroded terminal blocks. LiftMaster keypads are generally reliable, but the terminal block where the low-voltage wire lands is exposed to morning fog and Santa Ana dust. Corrosion builds on the terminals, and the opener starts behaving erratically – opening uncommanded, or ignoring the keypad entirely. We clean or replace the terminal block, then coat the connections with dielectric grease so the next North Hollywood winter does not undo the repair.
- Elite SL3000 and Commercial door operators with misaligned photo eyes. These are heavier commercial and long-driveway operators, but they show up regularly on North Hollywood estate gates. The photo eyes get knocked out of alignment by gate vibration or a stray car bumper, and the gate refuses to close. The fix is usually a simple realignment, but the real problem is loose mounting brackets. We tighten the brackets and set the eyes correctly so a bump does not knock them out again.
Our LiftMaster Gate Repair Process
- 1
You call (925) 693-7978. A live person answers, asks what the gate is doing – or not doing – and schedules a visit that fits your day. No voicemail tree, no callback queue.
- 2
We diagnose on site. Our technician tests the opener, the limit switches, the board voltage, the wiring, and the mechanical hardware. On a LiftMaster, we check the specific failure points for the model line you have – not a generic once-over.
- 3
You get a written price before work starts. We tell you what is wrong, what it costs to fix, and whether an OEM part or a quality aftermarket part makes more sense. We do not turn a wrench until you approve the number.
- 4
We make the repair. Most LiftMaster jobs are done in one visit. We carry common LA400, CSL24V, and K74 parts on the truck, so there is no waiting on a second appointment unless your opener is an unusual model.
- 5
We test the full cycle at least ten times. Open, close, stop, reverse, photo eye, keypad, remote. If it fails one test, it is not done.
- 6
We clean up and hand you the 90-Day Done Right Promise. Written, simple, no fine print to argue about. If it is not right, we come back and make it right.
What LiftMaster Gate Repair Costs in North Hollywood
Most LiftMaster gate repairs in North Hollywood fall between $185 and $640, depending on what failed. Here are honest ranges from our own job history, not a national chart:
- Limit switch replacement on an LA400 or LA500: $185 – $280
- Control board replacement on a CSL24V or CSW24V: $320 – $480 (includes surge protection)
- Photo eye realignment or sensor replacement: $95 – $220
- Keypad repair or replacement (K74/K75): $140 – $260
- Gearbox rebuild on an MCT or MCT-3: $260 – $420
- Full diagnostic visit with no repair needed: $89 (credited toward the repair if you proceed)
What moves the price: whether you need an OEM board versus an aftermarket equivalent, whether the gate is a slide or a swing, and whether we are also fixing damaged hardware – hinges, posts, or welds. You will never see a surprise line item on the final invoice. The price we quote is the price you pay. Call (925) 693-7978 for a free estimate on any LiftMaster repair over $250, and ask about the $50 discount we run on those jobs.
Why North Hollywood Homeowners Call Ironworks Gate Co. for LiftMaster Work
We have been working on gates in this city for over 42 years, and we have seen every LiftMaster model this city has adopted – from LA400s on Toluca Lake driveways to CSL24Vs behind the gates in Valley Village. Our technicians are trained on nine gate automation brands, so if your LiftMaster shares a driveway with a Mighty Mule, Ghost Controls, or DoorKing on another gate, we handle that too. Every visit is a single technician, background-checked, uniformed, and working the way he would in his own mother’s driveway. The 90-Day Done Right Promise is written on every invoice – not a slogan. Done right, and backed in writing.
FAQs
No. As an independent LiftMaster service provider, the work we perform is done using OEM parts and factory-specified procedures whenever possible, which keeps the original warranty intact. If your opener is still under warranty, we will tell you before any work begins and will help you file the claim if the failure is covered. We will not recommend a repair that voids coverage.
In most cases, we can have a technician at your gate the same day or the next morning, depending on when you call. Our live-answer team schedules around your availability, and for a gate stuck open or refusing to close, we treat it as urgent. A gate should open when you need it to and stay closed when you don’t.
We stock common boards, limit switches, keypads, and photo eyes for the LA400, LA500, CSL24V, CSW24V, and K74/K75 lines on our trucks. If your opener needs a less common part, we order it direct and install it within a few days. We never install a knockoff board that fails six months later to save a buck on the front end.
If the opener is under 10 years old and the repair is under half the cost of a new unit, repair usually makes more sense. If the board has failed twice in two years, or the motor is drawing high amperage and running hot, replacement is the honest answer. We will show you the numbers and let you decide – no pressure, no upselling. Call (925) 693-7978 and we will give you a straight assessment.
Contact Ironworks Gate Co. for LiftMaster Repair in North Hollywood
If your LiftMaster gate is acting up, call (925) 693-7978. You will speak with a live person who knows these openers, and we will schedule a visit that fits your day. Free estimates on repairs over $250, a written price before any work starts, and the 90-Day Done Right Promise on every job. Victor Salinas and the Ironworks team have been serving North Hollywood and the surrounding Valley for over four decades – and we plan to be here for another forty.
Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving North Hollywood and nearby areas.