Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterTrusted Gate Parts & Welding for North Hollywood Homeowners
Gate Parts & Welding - North Hollywood means one thing in practice: the frame, hinges, posts, and hardware that carry the full weight of your gate every single day. When a weld cracks or a hinge sags, the gate does not fail quietly. It drags, jams, or refuses to close, and that is when homeowners call us. Ironworks Gate Co. has served North Hollywood and the surrounding San Fernando Valley for over 42 years, founded in 1984 and led by Victor Salinas. We repair and replace gate hardware the way it should have been done the first time: squared, welded, and set to hold for decades. For urgent hinge or weld failures, call (925) 693-7978 and a live person answers, 24 hours a day, 7 days a week.
What Our Gate Parts & Welding Service Includes
Gate hardware is not interchangeable the way a light switch is. Every gate carries weight differently depending on its length, material, and how many times a day it cycles. Our Best Gate Parts & Welding in North Hollywood, CA covers the six areas that fail most often on local properties: hinges, posts, rails, custom welds, rollers, and latches. Here is what each involves and what we actually do on site.
Hinge Replacement
Hinges carry the entire load of the gate, and they wear unevenly on sloped driveways and in clay-heavy soil that shifts with the seasons. When a hinge begins to sag, you will see the latch side of the gate drop and start scraping the ground or the post. We remove the old hinge, inspect the post and gate frame for hidden cracking, and weld or bolt a properly rated replacement in place. Most hinge replacements on single driveway gates in North Hollywood are completed the same day we arrive.
Post Replacement
A leaning gate post is rarely just a post problem. It usually means the original footing was undersized, the post has rotted at the base, or a vehicle bumped it at some point and started a slow lean. We cut the old post free, remove it, and set a new steel post in a concrete footing sized for the gate’s weight and the soil conditions in your part of North Hollywood. In the hillside pockets east of the 170, where soil movement is common, we often recommend a deeper footing than the original install used.
Rail Repair
The top and bottom rails are the horizontal members that tie the gate frame together, and when one bows or cracks, the whole gate starts to rack out of square. We see this often on older wrought-iron gates where water has sat inside the rail and caused internal rust. We straighten or replace the rail, weld it square, and repaint the joint so the repair does not advertise itself. A rail repair done correctly should outlast the rest of the gate.
Custom Welding
Some gates are not worth replacing but need more than a bolt-on part. A cracked picket, a broken scroll, a torn weld at a corner joint – these are jobs for a torch, not a wrench. Our technicians are trained welders, not just parts swappers, and we fabricate and weld replacement sections on site when the gate design allows it. Victor Salinas has spent decades matching new metal to old so the repair disappears into the original work.
Gate Rollers
Sliding gates in North Hollywood ride on rollers that pick up grit, gravel, and fine dust from the dry wash of the Valley. When a roller seizes, the gate grinds instead of glides, and the motor works harder every cycle until something gives. We replace worn rollers with sealed or greasable units rated for the gate’s weight, and we check the track alignment at the same time. A new roller on a misaligned track is a wasted repair, so we always check both.
Latch & Lock
A latch that misses its strike plate is not a small annoyance. It means your gate is not actually secured, even when it looks closed. We realign, rebuild, or replace gate latches and locks, including the mechanical locks that pair with automation systems on estate gates. If your latch feeds a magnetic lock or a solenoid release on an opener, we check the whole chain so the lock and the motor are working together, not fighting each other.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service for Gate Parts & Welding
We service every major gate brand found on North Hollywood driveways, and our technicians carry the training and the parts to fix the hardware correctly the first time. On Viking systems, we regularly replace hinge pins and rebuild the heavy weldments that carry full-cantilever gates, and we keep Viking OEM parts on our trucks for the most common failures. House calls on Viking gates usually end the first visit, because we do not spend the afternoon chasing a part across town.
Studio City Gate Parts & Welding needs often involve Ghost Controls and DoorKing units, which appear constantly in the Valley, particularly on estate properties and hillside homes where the driveway elevation forces a custom installation. We have rebuilt hundreds of Ghost Controls hinge assemblies and swapped worn DoorKing roller trucks, always returning the gate to square before adjusting the motor limits. Elite gates, with their heavier steel profiles, respond best to welded repairs rather than bolt-on brackets, and that is exactly how we handle them. Whether your gate was built around a Viking, Ghost Controls, DoorKing, or Elite system – or any other make – we can diagnose and repair it on site.
Signs You Need Gate Parts & Welding Right Now
- The gate scrapes the driveway when it swings. This is nearly always a hinge or post problem. The gate is dropping because a hinge pin is worn through or the post has started to lean. Every cycle that scrapes puts more stress on the opener motor, which costs more to replace than a hinge will.
- You can see a crack in the metal, even a hairline one. Wrought iron and steel gates crack at stress points: corner welds, hinge mounts, and where the opener arm attaches. A hairline crack becomes a full break faster than most people expect, and a gate that breaks free mid-swing is dangerous.
- The gate makes a grinding sound when it slides. That sound is a roller that has stopped rolling. The wheel is flat-spotted and dragging on the track, and the motor is pulling the extra load every time. Replacing a roller is cheap. Replacing a burned-out motor is not.
- The latch does not catch cleanly anymore. When the gate does not positively latch, your property is not secure, even if it looks closed from the street. A misaligned latch also means the gate has shifted, and the causes of that shift tend to get worse without correction.
- The gate sags when held halfway open. Hold the gate at 45 degrees and take your hands away. If it drops or twists, the hinge bearings or the gate frame itself have failed. This is a structural issue, not a cosmetic one, and it should be addressed before the gate comes off its hinges entirely.
Our Gate Parts & Welding Process - Step by Step
- 1
We show up and listen. The technician walks the gate with you and hears what you have observed: when the noise started, which side binds, whether it has been hit recently. Most failed gates have a story, and the story usually points at the root cause faster than a guess would.
- 2
We measure and inspect under load. We check the gate’s level, square, and plumb with the gate both open and closed, because some failures only show themselves under load. We use a straightedge on the rails and a feeler gauge on the hinge pins to catch wear that a quick glance misses.
- 3
We quote the repair before any work starts. You get a written price for the parts and the labor, and that price is settled before a single bolt is turned. No open-ended hourly billing, no surprises on the invoice. Our word on the price is the price.
- 4
We repair, weld, or replace the failed parts. The work is done properly by a background-checked, uniformed technician who has done this same repair many times before. We carry the common parts on the truck, and when we weld, we weld to hold a gate that may need to cycle thousands of times before its next service.
- 5
We test the gate through full cycles and stand behind the work. Before we leave, the gate goes through repeated open-close cycles while we watch for binding, scraping, or noise. Every job carries our 90-Day Done Right Promise in writing: if it is not right, we come back and make it right, no paperwork and no arguing. The 400th job gets the same care as the first.
How Much Does Gate Parts & Welding Cost in North Hollywood?
A typical hinge replacement or gate roller replacement in North Hollywood runs $180 to $420 depending on the gate’s weight and how many hinges or rollers are involved. Post replacement is a bigger job because it involves concrete work: expect $600 to $1,400 for a standard steel post set in a new footing, with heavier custom posts running higher. Custom welding repairs, like a cracked frame joint or a broken scroll, generally run $150 to $500 depending on the size of the weld and how much fabrication is needed. Rail repair falls between $250 and $750, and a full latch and lock rebuild is usually $160 to $380. Every quote covers parts, labor, and disposal of the old hardware, and the price is agreed in writing before any work starts.
Three factors move the price: the weight of the gate, the condition of the surrounding structure, and whether the gate needs to be removed and rehung. A light single driveway gate is faster to repair than a heavy estate gate or a full cantilever slider. The best way to avoid overpaying is to fix a small problem before it becomes a structural one, and the best way to know the real price is to call us. Estimates are free, and we will tell you what you need and what you do not. Call (925) 693-7978 and get a straight number from a person who has actually looked at the gate.
Gate Parts & Welding Near North Hollywood - Our Service Area
Ironworks Gate Co. runs crews throughout the San Fernando Valley and into the surrounding foothills. We serve North Hollywood and the nearby communities of Studio City, Sun Valley, Tujunga, La Crescenta-Montrose, Van Nuys, West Hollywood, Beverly Hills, Los Feliz, and Hancock Park. Most repairs in North Hollywood are handled same-day or next-day, and our service area extends east into Gate Parts & Welding in Burbank and Gate Parts & Welding in Glendale with the same upfront pricing and written guarantee. From our home base of operations, we dispatch across the Valley without the long wait that comes from companies based farther out.
Serving North Hollywood, CA - Our Local Coverage Area
We’re based in the North Hollywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Gate Parts & Welding in North Hollywood
Gate parts and welding is the repair and replacement of the structural hardware that carries a gate: hinges, posts, rails, rollers, latches, and the welded steel frame itself. Unlike an opener or an electrical problem, this work involves cutting, welding, and setting metal so the gate hangs square and cycles cleanly. In North Hollywood, most parts and welding calls are for sagging hinges, cracked welds, leaning posts, and worn rollers on sliding gates.
Most hinge, roller, and latch replacements are completed in a single visit, usually within two to four hours including the full-cycle testing. Post replacement and custom welding can run a half day or a full day depending on concrete curing time and the size of the fabrication. We quote the timeframe before the work starts, and we will be there when we say. Call (925) 693-7978 for an honest time estimate on your gate.
Most hardware repairs in North Hollywood fall between $180 and $750 for hinges, rollers, latches, rails, and routine welding work. Full post replacement with new concrete runs $600 to $1,400. The exact price depends on gate weight, the condition of the surrounding steel, and whether the gate must be removed and rehung. Every estimate is free, written, and agreed before any work starts, so you know the number up front.
Yes, we repair and replace parts on Viking and DoorKing gates across North Hollywood, along with Ghost Controls, Elite, LiftMaster, FAAC, BFT, Linear, and Mighty Mule. Our technicians are trained and equipped on all nine brands, and we stock the most common OEM parts so the repair is usually completed on the first visit. Whatever brand is on your driveway, we can fix it. Call (925) 693-7978 for a free second opinion on any written estimate.
Yes, and a live person answers our phones 24 hours a day, 7 days a week. If your gate has come off its hinges, broken a weld, or will not close and secure the property, we treat that as an Emergency Gate Parts & Welding in North Hollywood, CA call and get a technician out as quickly as possible. You will never be routed through a voicemail tree or an answering service when your property is unsecured.
Every gate parts and welding job we complete in North Hollywood is covered by our 90-Day Done Right Promise, in writing. If the repair is not right, we come back and make it right with no paperwork and no arguing. We call it the Keystone Standard internally, and it applies to every job without exception. That is the company that makes a 40-year-old gate close like the day it was hung.
Clear the area around the gate so we can work safely, and if the gate is on an automatic opener, make sure the opener is disengaged or plan to have us handle that when we arrive. Remove vehicles from the driveway so we have room to swing and lay out the gate if removal is needed. We handle everything else: tools, parts, welding gear, and cleanup before we leave.
Schedule Your Gate Parts & Welding Service in North Hollywood Today
A sagging hinge or a cracked weld is not going to heal itself, and waiting costs more than the repair ever will. Call (925) 693-7978 for a free, no-obligation estimate on gate parts and welding in North Hollywood. A live person answers 24 hours a day, 7 days a week, and the price is settled before we touch a bolt. Done right, and backed in writing.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving North Hollywood since 1984.