FAAC Gate Installation Nationwide

FAAC Gate Installation in North Hollywood: What to Know First

FAAC gate installation in North Hollywood typically runs between $2,800 and $7,500 depending on whether you have a single swing gate, a sliding gate, or a double driveway setup. Most FAAC installations we handle are completed within 3 to 5 business days from the first measurement to final testing, and we quote every job in writing before a single bolt is turned. If you own a FAAC opener and the gate itself has failed, or you’re building a new gate around an existing FAAC motor, call (925) 693-7978 and a live person will answer, day or night.

Call (925) 693-7978

This page is written for homeowners in North Hollywood who already have, or are planning to install, a FAAC automated gate. We’re an independent FAAC service provider, not a factory affiliate. That matters because we make repair and replacement decisions based on what’s actually best for your driveway, not what a manufacturer’s warranty department prefers. Victor Salinas, our owner, grew up in the Lankershim Arts District and has spent four decades working on gate systems across this Valley. He’ll tell you straight what your FAAC needs, and what it doesn’t.

How FAAC Products Fail - and How We Fix Them

• FAAC 400 Series swing operators losing limit position. The 400 series is common on North Hollywood homes with single swing gates, and we see the same failure pattern year after year: the operator’s limit sensors drift out of alignment, usually after a gate post settles or a hinge wears. The opener still runs, but the gate slams past its stop or reverses mid-cycle. We reset and physically re-align the limits, then test the full open-close cycle under load, not just on the bench.
• FAAC 750 and 844 sliding gate operators with failing capacitor-start circuits. Sliding gates put constant strain on the start capacitor, especially on heavy steel gates along the wider lots in North Hollywood’s Valley Village and NoHo Arts District. A weak capacitor means the motor hums but won’t move the gate without a push. We keep OEM and heavy-duty aftermarket capacitors in the truck, because this is a known weak point on these models and waiting for a factory part means a driveway that stays closed for a week.
• FAAC hydraulic operators (the 770 and 990 series) developing internal bypass leaks. Hydraulic FAAC units are smooth and quiet when they’re right, but when the internal bypass valve starts leaking, the gate moves slower every week and eventually stalls mid-travel. Homeowners often assume the motor is dying and expect a full replacement quote. We open the unit, test the bypass pressure, and replace the valve cartridge if the motor itself is solid. That’s usually a $300 to $600 fix instead of a $3,000 replacement.
• FAAC E024U and E124 control boards losing programming after power surges. North Hollywood gets its share of brownouts and transformer blows during the summer months. FAAC control boards are sensitive, and a hard surge can wipe the travel limits and remote programming. The gate won’t respond, or it opens an inch and reverses. We don’t just reprogram the board; we check the grounding and add a surge suppressor at the operator if the homeowner will allow it, because fixing the symptom without addressing the cause means we’ll be back in August.
• FAAC photocell and safety-edge misalignment on double gates. Double swing gates with FAAC operators require synchronized leaf timing and properly aligned safety beams. When one leaf drifts ahead of the other, the safety edge can trigger and freeze the whole system. We see this most often on older installations where the original installer set the leaf delay incorrectly. We re-time both operators, check the edge sensor continuity, and run a full safety reversal test so the gate actually complies with current UL 325 standards.

Our FAAC Gate Installation Process

1. 1
   We come out and measure. We look at the gate’s weight, the post condition, the hinge type, the power source, and the FAAC model already in place or the one you’re considering. No charge for the estimate.
2. 2
   We give you a written price. Parts, labor, and any electrical work are spelled out line by line. You sign off before we start, and that number doesn’t move unless you ask for additional work.
3. 3
   We source the right parts. For FAAC jobs, we use OEM parts where it matters for warranty and compatibility, and quality aftermarket parts where they’ll outlast the original without costing more than they should. If we’re repairing rather than replacing, we tell you which is which and why.
4. 4
   We do the work in one visit, most of the time. For a straightforward FAAC operator replacement or a gate weld-and-install, we arrive with everything on the truck. No “we’ll be back next week with the part.”
5. 5
   We test it like we’re going to live with it. Full open-close cycles, safety reversal, obstacle detection, remote programming, and manual release check. We don’t call it done until it runs ten times without a hiccup.
6. 6
   We stand behind it. Every FAAC installation we complete is covered by our written 90-Day Done Right Promise. If it’s not right, we come back and make it right. No paperwork, no arguing.

What FAAC Gate Installation Costs in North Hollywood

Here’s what we typically quote for FAAC work in North Hollywood. These are real ranges, not teaser prices.

• FAAC swing operator replacement (labor included, existing gate and posts in good shape): $2,800 to $4,600
• FAAC sliding gate operator replacement on an existing track: $3,200 to $5,400
• New FAAC installation on a double swing driveway gate (gate, steel fabrication, operator, safety edges, keypad): $6,500 to $11,000
• FAAC control board replacement with reprogramming: $550 to $980
• FAAC hydraulic service (valve, seals, fluid, pressure test): $400 to $900

What moves the price: gate weight and material, post condition, whether the electrical run from the panel is short or fifty feet, and whether we need to add safety edges or a new keypad to meet code. We don’t charge for the estimate, and the price you sign is the price you pay. Call (925) 693-7978 for an exact quote on your FAAC gate.

Why North Hollywood Homeowners Call Ironworks Gate Co. for FAAC Work

We’ve been working on gates in North Hollywood and the surrounding Valley for over 42 years, since 1984. That’s long enough to have seen FAAC operators installed brand new, and long enough to know exactly what they look like when they’ve been neglected for a decade. Our technicians are trained on FAAC systems specifically, and they’re also current on LiftMaster, Mighty Mule, Ghost Controls, and DoorKing, so if your situation calls for a different opener than the one you had, we can give you a straight comparison without sending you to someone else. A live person answers our phone 24 hours a day, 7 days a week. When you call about a FAAC gate that won’t open, you get a human, not a voicemail tree. And every job, from a hinge weld to a full FAAC installation, carries our written 90-Day Done Right Promise. Done right, and backed in writing.

FAQs

Do you install FAAC gates that I bought from another supplier? Yes, we install FAAC operators and gates purchased elsewhere, as long as the equipment is in workable condition and compatible with your site. We’ll inspect it at the estimate and tell you plainly if what you bought is going to work or if it’s going to fight you for years.

Will installing a new FAAC operator void the factory warranty? As an independent FAAC service provider, our installation does not void the manufacturer’s warranty on the operator itself. We follow FAAC’s installation specifications carefully, and we document the work. If a factory defect shows up later, we’ll help you pursue the warranty.

Can you come today if my FAAC gate is stuck closed? For a gate that won’t open and is blocking your driveway, we prioritize same-day dispatch in North Hollywood whenever possible. Call (925) 693-7978 and we’ll tell you honestly what our schedule looks like. A live person will answer.

Should I repair my FAAC operator or replace the whole gate? Depends on the condition of the gate itself. If the steel is sound and the posts are straight, we can usually replace the operator and get another decade out of the setup. If the gate is rusting through or the posts have shifted, putting a new FAAC motor on a dying gate is throwing good money after bad. We’ll show you the numbers either way before you decide.

How long does a FAAC gate installation take? Most single-operator FAAC installations are done in one day. A full custom gate with new posts, concrete, and dual operators takes three to five days. We’ll give you a timeline with your written estimate and stick to it.

If you need FAAC gate installation in North Hollywood, call Ironworks Gate Co. at (925) 693-7978 for a free estimate. We’ll come out, measure, and give you a written price before any work starts. No surprises, no pressure, no callbacks you have to chase.

Written by Victor Salinas, Owner, Ironworks Gate Co. at Ironworks Gate Co., serving North Hollywood and nearby areas.