Linear Gate Motor & Opener Nationwide

Linear Gate Motor & Opener in North Hollywood: What to Know First

Linear gate motor and opener service in North Hollywood is what we do every week, and most repair jobs are finished in a single visit. A typical Linear opener repair in this area runs between $225 and $480, with full motor replacements ranging from $950 to $1,600 depending on the model and whether we’re reusing your existing receiver and safety edges. We’re an independent Linear service provider, not an authorized dealer, which means we stock common Linear parts on the truck and quote the price before any work begins.

Call (925) 693-7978

If you own a Linear gate opener in North Hollywood and it won’t open, grinds, or quit responding to remotes, this page is for you. Victor Salinas and the Ironworks Gate Co. crew have serviced Linear equipment across the San Fernando Valley since 1984. Call (925) 693-7978 and a live person answers, any hour, any day.

How Linear Products Fail - and How We Fix Them

Linear built its reputation on simple, durable swing and slide gate operators that were common in North Hollywood tract homes from the 1990s through the mid-2000s. The tradeoff is that simplicity. When something does fail, it tends to fail completely rather than gradually. Here are the five patterns we see most often on Linear gate motors and openers in this city:

• Linear LDO50 and LS050 limit switch drift. These aging swing and slide operators lose their open/close limit settings over time, causing the gate to stop six inches short or slam the post at full force. The fix is usually resetting the limit cams and adjusting the torque, not a new board. We see it most on gates that run more than 20 cycles a day, which is most busy North Hollywood driveways.
• Linear APeX and MegaCode receiver failure. The MegaCode receiver modules on the APeX series are known for slowly going deaf. The remote works when you’re close to the antenna, then one day it only works from inside the car two feet away. The cause is usually a degraded RF module or corrosion at the antenna whip, and we replace the receiver module rather than the whole opener where possible.
• Linear MDR/MDRG and SL series brush wear. Linear slide motors of a certain era use brushed DC motors. In the dry, dusty air of North Hollywood, brush dust builds up inside the motor housing and eventually causes jerky motion or a dead motor. If we’re in early enough, cleaning and brush replacement saves the motor. If it’s gone, we’ll suggest comparing the cost of a new motor versus a full opener replacement, and we’ll quote both honestly.
• Water intrusion in the control box. Our occasional winter downpours plus irrigation overspray are hard on Linear control boxes that were installed in the mid-2000s without weather-sealed conduit fittings. We open the box and find moisture beads inside, or worse, a fried control board. On replacement we re-drill the conduit entry, use sealed fittings, and add a desiccant pack. It costs an extra fifteen dollars and prevents the same failure next year.
• Worn plastic worm gear on Linear LDO33 and LDO50 arms. Linear actuator arms use a plastic worm gear that’s deliberately sacrificial, so the motor doesn’t burn out when the gate binds. If your Linear gate groans and moves slow before tripping, that gear is likely half-melted. We replace the gear and check the gate hinges at the same time, because binding hinges are what murdered it in the first place.

Our Linear Gate Motor & Opener Process

When you call Ironworks Gate Co. with a Linear gate problem in North Hollywood, here’s how the job goes from the first ring to the final test:

1. 1
   You talk to a person, not a recording. We ask what the gate is doing and what model Linear opener is on the post if you know it. That helps us load the right parts before we roll.
2. 2
   We arrive with the truck stocked for Linear. Our techs carry common Linear boards, limit switches, receiver modules, and actuator gears. Most North Hollywood calls are finished on the first trip because the part is already on the truck.
3. 3
   Diagnosis happens with the gate in front of us. We test the operator through a full open and close cycle, check the battery or power feed, inspect the safety edges and photo eyes, and tell you exactly what we found and what it costs before we touch a bolt.
4. 4
   Parts decision: OEM or quality aftermarket, your call. On most Linear repairs, OEM boards cost 30 to 50 percent more than a proven aftermarket equivalent. Where OEM matters for warranty or compatibility, we tell you that. Where aftermarket is equivalent, we tell you that too and let you decide.
5. 5
   The repair and the cleanup. We replace the failed component, set your travel limits, adjust force so the gate won’t injure a child or pet, and sync every remote and keypad you still use. We leave the driveway cleaner than we found it.
6. 6
   The 90-Day Done Right Promise, in writing. Every service call gets the Keystone Standard: if it’s not right, we come back and make it right, no paperwork, no argument. You’ll get that on your invoice, not just in a handshake.

What Linear Gate Motor & Opener Costs in North Hollywood

Linear gate motor and opener pricing in North Hollywood breaks into a few common scenarios. Here’s the reality of what we quote, settled before work begins:

• Diagnostic service call: $89, and if you approve the repair, that amount is credited toward the job
• Limit switch or travel adjustment service: $120-$190, no parts needed in most cases
• MegaCode receiver module replacement: $185-$260 installed
• Control board replacement (LDO50, LS050, SL series): $275-$450 installed, depending on OEM vs aftermarket board
• Full Linear opener replacement: $950-$1,600 including labor, depending on gate size and weight and whether we rewire or keep existing accessories
• Battery backup system install: $350-$600, which matters out here when the Santa Anas take down a power line

What moves the price: gate weight and condition, distance from the house electrical panel, whether your safety edges and photo eyes are still code-compliant, and how much of the old mounting hardware we can reuse. You’ll know the full number before the first bolt is turned. Call (925) 693-7978 for an exact quote on your gate, and estimates are free.

Why North Hollywood Homeowners Call Ironworks Gate Co. for Linear Work

We’ve been repairing and installing gate openers in North Hollywood for over 42 years, and we’ve been servicing Linear equipment since it was the most common opener in the Valley. Our techs carry Linear parts on the truck, not back at a parts counter, so most jobs are done in one visit. If the honest recommendation is that your old Linear has had it and a newer brand makes more sense for your gate, we stock and service eight other major brands: LiftMaster, Mighty Mule, Ghost Controls, DoorKing, and more. That’s the difference between a brand specialist and a gate specialist. A gate specialist works on whatever the gate needs.

Victor grew up in the Lankershim Arts District, trained in welding and fabrication at LATTC downtown, and has spent the last four decades learning every gate system North Hollywood can present. Around here, he’s known for showing up when he says he will and for not recommending a part you don’t need. A gate should open when you need it to and stay closed when you don’t. Everything else is just the work.

Frequently Asked Questions