Linear Hinge & Roller Replacement Nationwide

Linear Hinge & Roller Replacement: The North Hollywood Owner’s Guide

We stock and install Linear-compatible hinges and rollers for most residential swing and slide gate models, with typical replacement costs in North Hollywood running between $240 and $480 installed per hinge assembly, depending on gate weight and access. Most roller swaps are done same-day from parts on the truck, and we quote the full price before turning a single bolt. The usual phone call starts the same way: the gate has started dragging, screeching, or leaning, and the owner has been fighting it open for three weeks. By the time we arrive, the roller has usually worn flat on one side or the hinge pin has started to egg out the mounting hole.

Call (925) 693-7978

Which Linear Models This Applies To

Linear’s residential gate hardware shows up most often on the VS-GSLG slide gate series and the older LRA swing gate arms, but the hinges and rollers themselves are frequently sourced from the same industrial suppliers that feed LiftMaster and FAAC. That’s the compatibility gotcha worth knowing: Linear didn’t manufacture every hinge on every gate. On a 15-year-old Linear installation in North Hollywood, the rollers are often standard 4-inch nylon or steel-wheel units with a 5/8-inch bore, and the hinges are weld-on barrel or bolt-on plate style, typically rated for 600 to 1,200 pounds depending on the leaf size. The reliable way to identify what you have is to measure the roller diameter and axle bore, then check the hinge plate for a stamped part number. We keep OEM Linear parts for the current models and quality aftermarket equivalents where the original part number has been discontinued, which is increasingly common on gates installed before 2010. We are an independent service provider, not affiliated with Linear, which means we’re free to install whichever version of the part actually holds up best on your gate.

We also carry hinge and roller stock for LiftMaster, Mighty Mule, and Ghost Controls systems when a property has mixed-brand hardware or a previous contractor installed whatever was on the shelf.

Signs Your Linear Hinge & Roller Replacement Is Failing

• The gate drags or scrapes the ground on the latch side. This is the classic worn-roller signature. The wheel has gone flat on the bottom or the axle is wallowed out, dropping the gate a half-inch lower than it hung new. In North Hollywood, the combination of dry summers and damp winter mornings accelerates this because the gate’s weight sits on the same spot for weeks at a time.
• A squeal or metal-on-metal grind when the gate moves. Roller bearings fail first, usually after the factory grease breaks down. A quick tell is that the noise changes pitch as the gate picks up speed.
• The gate sags visibly at the hinge end. The hinge pin or barrel is worn into an oval, which lets the whole leaf drop and kick outward. This puts additional load on the opener motor, and on a Linear swing arm that means premature gear wear inside the operator.
• The gate stops short of the closed position or bounces when it seats. A failed roller on a slide gate changes the track engagement, and the operator’s limit settings no longer match the actual gate travel. The closing bounce is the gate hitting an obstruction that isn’t there.
• Fresh rust streaks bleeding from the hinge pin area. In North Hollywood’s marine-influenced air near the 170 corridor, pin-bearing rust is common on unpainted aftermarket hinges installed without grease fittings. Once the pin rusts, the wear accelerates quickly.

Replacement Cost & What’s Included

For a standard single-leaf Linear swing gate in North Hollywood, expect to pay $240 to $380 per hinge assembly replaced, parts and labor included. A heavier or double-leaf gate with slide rollers runs $320 to $480 per roller assembly, and if the mounting plate is so far gone that we’re welding a new plate to the post, the job moves to time and materials with the full amount agreed before the welder comes off the truck. Most hinge and roller replacements on Linear gates are one-visit jobs, somewhere between 90 minutes and three hours depending on whether we’re adjusting the gate’s throw, re-hanging the leaf, and resetting the operator limits, or just swapping a wheel. Every replacement is covered by our 90-Day Done Right Promise in writing, and the quote you approve is the price you pay. There are no surprises on the bill, and that’s not a slogan, it’s how we’ve run the shop for over 42 years.

DIY or Call Us?

For a homeowner comfortable with a jack, a level, and basic hand tools, checking the rollers and hinges is straightforward. You can look for a flat spot on the wheel, wiggle the gate by hand to feel for play at the pin, and spray the bearings with a dry lubricant to buy a few weeks. What we’d caution against is replacing a loaded hinge or roller yourself. The gate leaf weighs several hundred pounds and is under tension the entire time it’s off its supports. If it shifts while you’re under it, you’re not walking it off. A trained technician who has done this hundreds of times and who carries the right lifting gear and replacement hardware makes the job look simple because it is simple, for him. If you’re in North Hollywood and the gate is leaning or grinding, call (925) 693-7978 and we’ll be there when we say.

FAQs