Ghost Controls Gate Installation Nationwide

Ghost Controls Gate Installation in North Hollywood: What to Know First

Ghost Controls gate installation in North Hollywood usually runs $450 to $1,200 for a complete opener install on an existing gate, depending on the gate’s weight, the length of the power run, and whether we’re swapping out an old motor or starting fresh. Most Ghost Controls jobs are done in a single visit, and we quote the full price before any work begins. If your gate is already hung and you just need the automation side, we can typically get you on the schedule within a few days.

Call (925) 693-7978

This page is for North Hollywood homeowners who already own a Ghost Controls opener (or are about to) and need it installed correctly. We’re Ironworks Gate Co., an independent Ghost Controls service provider, and we’ve been installing and repairing gate systems in the Valley since 1984. Call (925) 693-7978 and a live person answers, day or night.

How Ghost Controls Products Fail - and How We Fix Them

Ghost Controls builds a solid residential opener, but every brand has its habits. Here’s what we see on North Hollywood driveways, and what we do about it.

• Battery drainage on the R Series. Ghost Controls R series openers rely on a 12V battery, and in North Hollywood’s summer heat, batteries that sit in direct sun degrade faster than the manual suggests. The symptom is a gate that opens fine for months, then suddenly won’t move at all. We test the battery under load, not just with a meter, because a battery can read 12.6 volts and still collapse the moment the arm starts pulling. Replacement is straightforward.
• Limit switch drift after power surges. The Ghost Controls TSS1 and TDS2 boards sometimes lose their open and close limits after a DWP power bump or a brownout. The gate will slam into the post or stop six inches short of full open. Owners assume the motor is dead. It usually isn’t. We re-set the limits, verify the obstruction sensor, and get it closing soft again.
• False obstruction trips from gate sag. Ghost Controls openers have a fairly sensitive obstruction detection circuit. If the gate has sagged even a quarter inch because the hinge post shifted in North Hollywood’s expansive clay soil, the opener reads that drag as an obstruction and reverses mid-cycle. A generalist will tell you to replace the opener. We’ll check the hinges, shim or weld the post as needed, and only then touch the opener. That’s the difference between a $200 hinge fix and a $900 motor you didn’t need.
• Remote and keypad pairing failures after battery swaps. Ghost Controls remotes and wireless keypads occasionally unpair themselves when the main battery is disconnected for more than a few minutes. The owner replaces a battery, then nothing responds. It’s a pairing sequence issue, not a board failure. We re-pair the accessories on site in about fifteen minutes.
• Arm mounting brackets loosening on heavy gates. Ghost Controls arms are well built, but the factory mounting brackets are sized for average residential gates. On a heavy steel double gate, the bracket bolts can work loose within a year, especially if the gate catches wind. We often upgrade the bracket hardware or reinforce the mount point while installing, and we check it as part of any tune-up.

Our Ghost Controls Gate Installation Process

A Ghost Controls installation isn’t a bolt-it-on-and-drive-away job. Here’s how we work, start to finish.

1. 1
   Phone call and walkthrough. You tell us what gate you have, what Ghost Controls model is in the box (or already on the post), and what it’s doing or not doing. We give you a straight answer about whether this is a same-day repair or a scheduled install.
2. 2
   On-site inspection and measurements. We check gate weight, hinge condition, post stability, and the distance from your electrical panel to the gate. We also check clearance for the arm’s arc of travel. If the gate itself needs welding or hinge work, we tell you that before anything else.
3. 3
   Written quote. You get the full price before we turn a single bolt. No surprises. The quote is agreed, then work starts.
4. 4
   Parts decision. We use Ghost Controls OEM parts when warranty coverage matters and the part is available. For older models where OEM is discontinued or backordered, we’ll tell you honestly and use a quality aftermarket equivalent that matches spec. You’ll know which is which before we order or install anything.
5. 5
   Installation and wiring. We mount the arm, run the power, set the limits, pair the remotes and keypad, and test the obstruction sensor multiple times. If there’s a safety edge or photo eye, that’s wired in and verified.
6. 6
   Cleanup and the test you watch. We walk you through the operation, you test it yourself while we stand there, and then we hand you the written 90-Day Done Right Promise. That’s the Keystone Standard on every job we do.

What Ghost Controls Gate Installation Costs in North Hollywood

Here’s what North Hollywood homeowners can expect to pay for Ghost Controls installation, based on the jobs we see most often.

• Basic single swing gate install with existing electrical nearby: $450 to $700
• Double gate install with two arms and a longer power run: $850 to $1,200
• Full install including a new post or hinge work: $1,100 to $1,800, depending on the welding
• Retrofit replacing an older opener (any brand) with Ghost Controls: $550 to $900, including removal and disposal of the old motor

What moves the price is the gate’s weight, the distance from your panel, and whether the gate itself needs structural work before the opener goes on. We quote the full amount before starting, and estimates are free. Call (925) 693-7978 and we’ll give you a number you can plan around.

Why North Hollywood Homeowners Call Ironworks Gate Co. for Ghost Controls Work

We’ve been working on driveway gates in North Hollywood since 1984. Victor Salinas grew up in the Lankershim Arts District, learned welding at LA Trade-Tech, and has spent the four decades since then fixing every kind of gate system this city has thrown at him. That experience matters when a Ghost Controls opener isn’t behaving and the fix isn’t obvious.

We’re equipped and trained on nine automation brands, so if the problem turns out to be something other than the Ghost Controls unit, we can handle it without calling someone else. LiftMaster, Mighty Mule, DoorKing, FAAC, BFT, Linear, Viking, Elite, and Ghost Controls: we service them all. And since we’re not a handyman service trying to figure out gates on your dime, we diagnose correctly the first time. Every job is backed by our written 90-Day Done Right Promise. If it’s not right, we come back and make it right. No paperwork, no arguing.

FAQs