Mighty Mule Gate Access Control Nationwide

Mighty Mule Gate Access Control in North Hollywood: What to Know First

We service Mighty Mule gate access control systems throughout North Hollywood, and most jobs are completed in a single visit. Expect an honest diagnosis first: if your keypad just needs a new board, that’s what we’ll tell you; if the whole operator is past saving, we’ll tell you that just as plainly. We quote the price before any work starts, and every repair is backed by our written 90-Day Done Right Promise.

Call (925) 693-7978

This page is for Mighty Mule owners in North Hollywood who are dealing with a keypad that won’t unlock, a remote that stopped working, or a phone-entry system that has gone quiet. Call (925) 693-7978 and a live person answers, any hour, any day.

How Mighty Mule Products Fail - and How We Fix Them

Mighty Mule is a common sight on North Hollywood driveways, and after four decades of servicing them, we know their habits. The failures we see on access control jobs are rarely the motor itself. They’re in the peripherals: keypads, receivers, wiring, and the small boards that tie them together. Here are the five we see most.

• FM350 keypad buttons that need a hard press (or fail entirely). The membrane keypad on the FM350, and on the older MM371W, wears unevenly in the North Hollywood sun. The top row, where people punch in their code, gets cooked by UV and the contacts underneath stretch. We replace the keypad module with a sun-tolerant aftermarket unit rather than swapping the whole board, which saves a couple hundred dollars.
• RB741 receiver that only works from ten feet away. This is a North Hollywood classic: the receiver antenna wire gets pinched inside the operator box, or the receiver itself is a 2008-era unit that was never great past twenty feet. We relocate the antenna outside the metal housing and, if the receiver is dead, install a newer 372LM-compatible receiver with the same wiring footprint so your existing remotes still work.
• MM260 swing gate opener that opens for a keypad but not for a remote, or vice versa. The MM260 runs both a keypad and a remote through a single learning circuit. When that circuit gets flaky, one input still works and the other doesn’t. It looks like a bad remote or a bad keypad. It’s usually neither. We test each input separately, then replace the small logic chip rather than condemning the operator.
• Phone entry systems that ring once and drop the call. Mighty Mule’s phone entry line, sold as an add-on for the MM and FM series, has a known cold-start issue: the relay doesn’t hold when the operator control board is sharing a transformer with the phone module. We see this on older North Hollywood installs where the original wiring was undersized. The fix is a dedicated transformer and a fresh relay, not a new phone module.
• Keypad codes that erase themselves after a power flicker. DWP power flickers are common enough in parts of North Hollywood fed by aging lines. Mighty Mule control boards don’t have non-volatile memory on the entry-code side; a quick brownout wipes the code and the owner thinks the keypad failed. We install a small memory-protection capacitor on the board and re-teach the code, then test it by cycling the gate breaker off and on.

Our Mighty Mule Gate Access Control Process

Here’s how a Mighty Mule gate access control job goes at Ironworks Gate Co., from first call to final test.

1. 1
   You call (925) 693-7978. A live person answers, day or night. We ask what the gate is doing, what’s on the driveway, and which Mighty Mule model you have. We book a time and we show up when we say.
2. 2
   Diagnostics at the gate. Our technician tests each access component separately: keypad, remote receiver, phone module, card reader, intercom. We don’t guess. We run a meter over the wiring, check voltage at the board, and isolate the actual failure.
3. 3
   Straight recommendation, straight price. If the part is worth saving, we say so. If a quality aftermarket part will outlast the original, we say so. If the OEM part is the right call, we use it. We write the price down and you approve it before a single bolt moves.
4. 4
   The repair. Most Mighty Mule access control work happens at the operator box and the keypad, so the job is usually finished in one visit. We solder, crimp, and seal connections like a blacksmith who also understands a control board.
5. 5
   Testing. We cycle the gate twenty times from every input: keypad, remote, phone, card, intercom. We open the breaker and run it again. Then we walk you through it.
6. 6
   Done Right, in writing. Every Mighty Mule access control repair carries our 90-Day Done Right Promise. If it isn’t right, we come back and make it right. No paperwork, no arguing, no exceptions.

What Mighty Mule Gate Access Control Costs in North Hollywood

Here are real numbers for the work we do most on Mighty Mule systems in North Hollywood.

• Keypad replacement or repair: $140-$320, depending on whether we’re replacing the module or the entire keypad housing
• Remote receiver replacement: $180-$280, including programming existing remotes
• Phone entry system repair: $220-$450, depending on whether the relay or the module is the problem
• Card reader install for Mighty Mule: $380-$700, including the reader, wiring, and programming
• Video intercom integration: $600-$1,200, depending on run length and existing low-voltage paths

What moves the price is access to the operator box, the age of your wiring, and whether you want OEM or quality aftermarket parts. We’ll quote the number before we start, and that’s the number on the bill. Call (925) 693-7978 for a free estimate on your Mighty Mule gate access control in North Hollywood.

Why North Hollywood Homeowners Call Ironworks Gate Co. for Mighty Mule Work

We’ve been serving North Hollywood and the surrounding Valley for over 42 years. Victor Salinas grew up in the Lankershim Arts District, watching the metal shops along the boulevard do work worth admiring, and the standard stuck. We’re an independent Mighty Mule service provider, which means we fix what’s broken instead of selling you a new operator when a $40 part will do.

Our technicians are trained and equipped on nine gate-automation brands, so if your Mighty Mule access control issue turns out to be something deeper, we’re not scratching our heads. We also service LiftMaster, Ghost Controls, and DoorKing on the same visit if that’s what’s actually on the driveway. Every job is covered by the 90-Day Done Right Promise, and a live person answers our phone 24 hours a day, 7 days a week. A gate should open when you need it to and stay closed when you don’t. Everything else is just the work.

FAQs