Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Parts & Welding Across West Hollywood
Gate parts and welding in West Hollywood, CA most often means one of three things: a hinge post that has rusted through at the footing, a sagging gate leaf that scrapes the driveway on a steep hillside grade, or a legacy operator that needs a retrofit rather than a full replacement. We handle all three, and we quote the work before we start. Call (925) 693-7978 and you’ll reach a live person, not a voicemail tree.
Our Gate Parts & Welding crews work throughout the 90069 ZIP code, from the flats near Santa Monica Boulevard up into the Bird Streets above Sunset. We know what the marine layer does to steel post footings here, and we know which hinges on a 1940s courtyard gate were never meant to carry an automated opener retrofitted in 2005. That local knowledge changes the repair we recommend.
Why Ironworks Gate Co. Is West Hollywood’s Preferred Gate Parts & Welding Company
West Hollywood has no shortage of generalist contractors who will weld a cracked rail. What it has fewer of is a gate-specific shop that has been doing this work for over 42 years and carries tooling for nine major automation brands. Our West Hollywood customers tend to be property managers and long-time homeowners who have already been burned once, sometimes twice. They are not looking for the cheapest weld. They want the gate to close like it did twenty years ago, and they want a written promise behind the work.
We serve the area from our Los Angeles dispatch office, with crews that work West Hollywood routes regularly. Response time to most addresses in 90069 is same-day for urgent repairs, and every job, from a hinge replacement to a full post footing rebuild, is protected by our 90-Day Done Right Promise. If it is not right, we come back and make it right. No arguing, no paperwork, no exceptions. That is the Keystone Standard, and it applies to a $200 latch repair the same as a $12,000 custom gate build.
Victor Salinas, who leads our shop, has rebuilt gates on Sunset Boulevard estates where the original operator still works because the mechanical foundation underneath it was maintained. That is the approach we bring to Gate Installation - West Hollywood: fix the metal first, then the motor. A gate operator on a misaligned leaf burns through its capacitor and gearbox far sooner than one hung true.
Our Gate Parts & Welding Services in West Hollywood
Hinge Replacement
Hinge replacement is the most common gate repair we perform in West Hollywood, and it is rarely a simple swap. On older gates, the hinge pin has often worn an oval into the bracket, which means a new pin alone will not fix the sag. We remove the gate leaf, weld in a fresh bracket or rebuild the existing mount, and re-hang the leaf so it swings without dragging. On hillside properties above Sunset Blvd, we regularly see hinge stress far beyond what flat-lot gates experience, because the gate is fighting gravity on every cycle.
A typical hinge replacement in West Hollywood runs $220 to $480 per hinge depending on gate weight and whether the mounting plate needs welded repair. We quote it before we begin.
Post Replacement
Post replacement is the job that separates gate specialists from general welders. In West Hollywood, where the marine layer settles overnight with persistent coastal moisture, steel hinge posts corrode at ground level even on properties that never see standing water. The failure happens inside the footing, invisible until the post starts leaning. We cut out the failed post, weld in a new powder-coated steel post with a deeper footing, and reset the gate. On 1920s and 1940s courtyard properties, the original posts are often non-standard diameters, which means the replacement must be custom-cut and welded on site rather than ordered from a catalog.
Post replacement in West Hollywood typically runs $680 to $1,500 depending on post height, footing depth, and whether concrete work is required. Many jobs on steep Bird Streets driveways trend toward the higher end because the footing excavation is more involved.
Rail Repair
Gate rails crack. It is what they do after thirty years of daily cycles, especially when the gate was retrofitted with an operator that pulls harder than the original design anticipated. We repair or replace top and bottom rails, straighten bent sections, and reinforce stress points where the operator bracket bolts to the frame. Mismatched hardware on West Hollywood’s older bungalows, where the gate was added decades after the house was built, often leaves rail spacing that is not standard, so we fabricate the repair to fit what is actually there.
Rail repair in West Hollywood runs $180 to $520 depending on the extent of the crack and whether we are reinforcing an existing rail or fabricating a replacement section.
Custom Welding
Custom welding covers a lot of ground: re-welding a broken picket, fabricating a new hinge mount, extending a gate that no longer meets a widened driveway, building a custom bracket for a non-standard operator arm. Our welders work with steel, aluminum, and wrought iron, and we grind, prime, and finish every weld so that the repair does not flash rust within a season. On hillside properties near the 90069 ridgeline, we specify powder-coated finishes and marine-grade hardware wherever moisture exposure is chronic.
Custom welding in West Hollywood runs $140 to $320 per hour, and we quote the hours before the torch is lit.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in West Hollywood
Our technicians are factory-trained on nine gate-automation brands for West Hollywood Gate Motor & Opener systems, including Viking, Ghost Controls, and DoorKing. That matters in West Hollywood specifically, because many of the estate gates here run on commercial-grade operators that a general handyman has never opened. We stock common control boards, limit switches, and capacitor kits for these brands in our service vehicles, which means most parts replacements happen on the first visit rather than after a week of parts shipping. If your gate runs on an Elite operator, we service those too.
Common Gate Parts & Welding Problems We See in West Hollywood Homes
- Corroded post footings from marine-layer moisture. The overnight coastal air in West Hollywood settles on steel post bases and works into the footing joint. Over five to ten years, the post rusts through at ground level and the gate begins to sag. This is the single most common structural failure we see across 90069.
- Burned-out swing gate motors on steep driveways. Gates on hillside parcels above Sunset Blvd fight gravity on every open and close cycle. A motor sized for a flat lot will overheat, and the gearbox will strip, sometimes within three to five years of installation.
- Mismatched hardware from post-construction retrofits. Many West Hollywood homes built in the 1920s through 1940s had no gate at all. When a gate was added in the 1990s or 2000s, the contractor often used whatever post spacing the driveway allowed, which means non-standard geometry that cracks welds and stresses hinges over time.
- Obsolete control boards on legacy operators. We regularly see FAAC, Viking, and DoorKing operators from the 1990s and early 2000s that still have mechanical life left, but the control board is no longer manufactured. Replacing the board with a current unit keeps the existing motor and gearbox in service for years more, which is almost always cheaper than swapping the entire operator.
Pricing for Gate Parts & Welding in West Hollywood, CA
Here is what you can expect to pay for common Gate Parts & Welding work in West Hollywood in 2026. These are real ranges, not placeholders: hinge replacement runs $220 to $480 per hinge. Post replacement runs $680 to $1,500. Rail repair runs $180 to $520. Custom welding runs $140 to $320 per hour. A full legacy operator retrofit, including control board replacement and safety sensor update, runs $850 to $1,800 on most single-leaf gates, and $1,400 to $2,800 on double-leaf estate gates.
What moves the price is gate weight, footing depth, and hillside access. A post replacement on a steep Bird Streets driveway requires more excavation and shoring than the same post on a flat lot near Santa Monica Boulevard. We price the job before we start, we honor that price, and we stand behind the work with our 90-Day Done Right Promise. Estimates are free. Call (925) 693-7978 and ask for a written quote.
We Also Serve Cities Near West Hollywood
Our Gate Parts & Welding in West Hollywood service area extends into the surrounding communities, including Beverly Hills, Studio City, North Hollywood, and Sherman Oaks. If you manage properties across the hills, we can schedule multiple gate repairs in a single route, which keeps dispatch costs down.
Serving West Hollywood, CA - Our Local Coverage Area
We’re based in the West Hollywood area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in West Hollywood
Yes, in most cases you do. West Hollywood operates its own building permitting authority, entirely separate from the City of Los Angeles, and any post replacement or custom welding that alters gate structure requires a WeHo building permit and inspection. This is a step many LA-based contractors skip, and it leaves property managers with unpermitted work that surfaces during resale and complicates future repairs. We handle the permit paperwork for post replacement and structural welding as part of the job. Call (925) 693-7978 and we will tell you exactly what your specific gate needs before we start.
In West Hollywood, the most common cause of recurring motor failure is a gate that is slightly out of alignment on a sloped driveway. On hillside parcels above Sunset Blvd, the gate fights gravity on every cycle, and a leaf that is even a half-inch off true multiplies the load on the gearbox and capacitor. The motor burns out because it is working against a mechanical problem, not because the motor is defective. We correct the hinge alignment and post footing first, then address the operator through Gate Access Control in West Hollywood. That fixes the root cause instead of replacing motors on a cycle.
In most cases, yes. The mechanical parts of a 1980s-era operator, the gearbox and the motor housing, often have years of life left. What is obsolete is the control board, which may not support current photo-eye and auto-reverse safety standards. We retrofit the operator with a current control board from the same brand, typically Viking, Ghost Controls, DoorKing, or Elite, and add the required safety edges and photo sensors. The original motor stays in place. This runs significantly less than a full operator swap, and it brings the gate into compliance without touching the gate leaf itself. Call (925) 693-7978 for a free estimate.
Usually not. A sagging gate is almost always a hinge and post problem, not a panel problem. The hinge pins wear, the brackets stretch, and on West Hollywood properties the post may have corroded at the footing. We remove the leaf, rebuild or replace the hinge mounts, re-hang the gate, and in most cases the panel itself is completely serviceable. Replacing the panel without fixing the underlying post and hinge geometry means the new panel will sag within a few years too. We will tell you honestly whether a panel is worth saving, and we quote the repair before any work starts.
We weld steel, aluminum, and wrought iron, and we match the filler metal to the base metal of your gate. For West Hollywood’s hillside and marine-layer conditions, we default to primed and powder-coated steel for structural components, and we specify stainless or hot-dip galvanized hardware for hinge pins and mounting bolts so that coastal moisture does not start the same corrosion cycle over again. If the original gate is aluminum, we weld with the appropriate aluminum filler and finish to match. Call (925) 693-7978 and describe your gate; we will tell you what metal it is and what the repair requires.
Call Ironworks Gate Co. for Gate Parts & Welding in West Hollywood
If you have a gate that sags, a post that leans, a motor that will not stop burning out, or a control board that is older than your tenants, call (925) 693-7978. You will get a live person, a straight answer, and a written price before we touch a bolt. We serve the full 90069 ZIP code, from the flats to the Bird Streets, and we stand behind every job with the 90-Day Done Right Promise. Free estimates, upfront pricing, and a gate that works like it should.
Written by Victor Salinas, Owner at Ironworks Gate Co., serving West Hollywood with gate parts and welding since 1984.